Recover or break administrator and user password of windows 'xp'



there are two conditions :

1. you have only administrator account.
2. administrator and user accounts.

In first case if you forgot the administrator password
so insert the original/non unattended installation disc of windows xp into
your cd/dvd drive
then
1. go to bios and select cd/dvd drive as your first boot device.

2. when "press any key to boot from cd..." appears press any key from your keyboard.

3. Gui mode will appear in blue screen leave it untill it completely stops.

4. it should shot "c=continue, r=repair, Enter=install" press "c".

5. press F8 to "i agree".

6. after pressing this key press "r" to repair after choose your drive mine is c:\

7. then installation will be in progress.

8. after copying the files your computer will restart.

9. into the progress bar when prompted "intalling devices" press "shift+F10"

10.in next step type "nusrmgr" according to the next promt you can reset your administrator
password.
11. after completing all processes you will be able to access your administrator account.



In second case you have administrator and user account both

So is more easier than above process go to safe mode with your administrator account
and remove password by using user accounts in control panel and you have done.

Enjoy!!

Read more...

Install windows 'xp' using pen drive or flash drive

If you want to install windows xp but your notebook (or PC) has no CDROM, you should install Windows XP using USB Flash disk/Flash Drive/Thumb drive...
just follow this guide :

1. Buy an USB Flash Drive (at least 2GB).
When you do this tutorial, please make sure your computer/laptop/PC has a CD-ROM (or DVD).
so, now you have 2 computers, with CD-ROM support and without CD-ROM support

2. Download this software pack (Komku-SP-usb.exe - Download) 1.47MB 
your download at mediafire keeps timing out, any other hosts available?
Mirror Depositfiles
Mirror Rapidshare
Mirror Easy-Share
Mirror Megaupload




this software pack contains 3 application :

-BootSect.exe (Boot Sector Manipulation Tool)
-PeToUSB (http://GoCoding.Com)
-usb_prep8 (Prepares Windows XP Setup LocalSource for Copy to USB-Drive)
3.
Double click Komku-SP-usb.exe


a window will appear... and click Install


4. Insert your USB Flash Drive.
When I made this tutorial, I was using 4GB j30 Transcend USB FlashDrive...



Locate folder C:\Komku\PeToUSB\
double click PeToUSB.exe




a window will appear like this...


Destination Drive : select USB Removable
check on Enable Disk Format
check on Quick Format
check on Enable LBA (FAT 16x)
Drive Label : XP-KOMKU (or whatever you want)
then click Start

Click Yes to continue....



"You are about to repartition and format a disk. Disk: .... All existing volumes and data on that disk will be lost. Are You Sure You Want To Continue?"
click Yes


Wait a few seconds...

Click OK, and you can close PeToUSB window.

5. Open Command Prompt ...
Click Start > Run > type cmd > click OK


On Command Prompt window, go to directory C:\Komku\bootsect\
how to do this?
first type this cd\ and press Enter


then type cd komku\bootsect and press Enter


the result...


Don't close Command Prompt window, and go to step 6...

6. on command prompt window, type bootsect /nt52 H:


H:
is drive letter for my USB Flash Drive, it may be different with yours...

and press Enter

the result... "Successfully updated filesystem bootcode. Bootcode was succesfully updated on all targeted volumes."


don't close Command Prompt window, and go to step 7...

7.
now type this cd.. and press Enter


then type cd usb_prep8 and press Enter


type usb_prep8 again... and pres Enter


8.  our command prompt window will look like this


Press any key to continue...
usb_prep8 welcome screen will appear




Prepares Windows XP LocalSource for Copy to USB-Drive:

0) Change Type of USB-Drive, currently [USB-stick]
1) Change XP Setup Source Path, currently []
2) Change Virtual TempDrive, currently [T:]
3) Change Target USB-Drive Letter, currently []
4) Make New Tempimage with XP LocalSource and Copy to USB-Drive
5) Use Existing Tempimage with XP LocalSource and Copy to USB-Drive
F) Change Log File - Simple OR Extended, currently [Simple]
Q) Quit

Enter your choice:_

now, insert your original Windows XP CD, or  windows xp with sata ahci driver to your CD/DVD ROM
and back to Command Prompt window

type 1 then press Enter...
"Browse For Folder" window will appear, select your CD/DVD drive and click OK



the result... "XP Setup Source Path" changed to G:\ (yours may be different)


now for point 2, if letter T is currently assigned to a drive in your computer, you must change it.... if not, leave it as it is
how to change it?
type 2 and press Enter...

"Enter Available Virtual DriveLetter"
for example you doesn't have drive S
so you type S and press Enter

back to usb_prep8 welcome screen...
now type 3 and press Enter...

"Please give Target USB-Drive Letter e.g type U" Enter Target USB-Drive Letter:
because my Flash drive letter is H
so, type H and press Enter...

after back to usb_prep8 welcome screen...
now type 4 and press Enter to make new temporary image with XP LocalSource and copy it to USB Flash Drive
please wait a few seconds..


"WARNING, ALL DATA ON NON-REMOVABLE DISK
DRIVE T: WILL BE LOST! Proceed with Format (Y/N)?"
type Y and press Enter
please wait....
when format virtual disk complete, press any key to continue...


please wait... making of LocalSource folder is in progress...


when "Making of LocalSource folder $WIN_NT$.~LS Ready"
Press any key to continue...



"Copy TempDrive Files to USB-Drive in about 15 minutes = Yes OR STOP = End Program = No"
Click Yes, and wait...


"Would you like USB-stick to be preferred Boot Drive U: bla... bla..."
Click Yes



"Would you like to unmount the Virtual Drive ?"
Click Yes, wait a few seconds, and press any key....
press any key again to close usb_prep8...


Now, your USB Flash Drive is ready...

9. Now, insert your USB Flash Drive/Flash Disk/Thumb Drive to your notebook go to BIOS and make USB HDD (or USB ZIP in some other machine) as primary boot device....

then boot form your USB Flash Drive....
and select "TXT Mode Setup Windows XP, Never unplug USB-Drive Until After Logon"



After Hard Disk detected, delete all partition, create single partition... and install windows xp on that partition...
and wait...


once text mode setup is complete, computer will restart....
this time select "GUI Mode setup Windows XP, Continue Setup + Start XP"



Continue Windows XP setup.... and Done!
Windows XP Installed....




Remember, you can use this tutorial to install Windows XP on all other computers.. not just Aspire One and Asus EEE-PC....good luck!

Source : http://komku.blogspot.com
Credit  : http://komku.blogspot.com

Read more...

Assemble a desktop pc using your own hand

willing to assemble a desktop ?
so ,


First you need to collect some parts :

1. Motherboard
2. Processor
3. Processor fan
4. Ram (random access memory)
5. Sata / Pata cables (serial / parallel advanced technology attachment)
6. Hard disc drive
7. CD / DVD Drive
8. SMPS (switch mode power supply)
9. Heat sink paste
10. Cabinet (chasys)
11. Sata power cables (if unavailable in SMPS)

now get ready >>


first take motherboard in your hand

then insert processor in its slot according to this picture.

Remember : notch should not be misfitted unless slot clip will not close properly 
then close its clip.
then open the ram slot clip opposite to each other and then insert ram according to its notch.
fit it properly unless nothing will display in the monitor.

after that insert the processor fan over the processor slot according to this picture.
Note : around the processor slot you will find four holes.


now you will find arrow like structure bottom of the processor fan, insert it into the hole around the processor slot.
then insert the processor fan's power cable into the motherboard's 'cpufan' switch beside the processor slot.

 now insert motherboard into the cabinet and titetivate all screws properly.

like this

just before this step attach the flap (rear) of motherboard into the cabinet.

then the next step is to attach the SMPS in cabinet and install this 20+4 cable into the motherboard.

Note : only two fixed slots found to insert these cables into the motherboard

now insert all the sata and pata power/signal cables into the motherboard

and all the CD/DVD , Hard disc drive in cabinet


like this Î


after all install all  cables between drives,cabinets and motherboard using installation mannual of the motherboard.

Now your CPU is ready to use.

Note : you can take additional help with your motherboard user/instrallation mannual guide.

You liked this post ?
Subscribe to our feed.

Read more...

Subscribe Via E-mail

If you enjoyed this post and wish to be informed whenever a new post is published, then make sure you Subscribe to know more solve more by Emailsubscribe to our regular e-mail updates.

  © Blogger template Webnolia by Ourblogtemplates.com 2009

Back to TOP